insulating paints and insulating paint additives Clear Waterproof Elastomeric Sealer
spaceage insulating ceramicsA NASA Technology Spinoff Company 2003spaceage insulating ceramics
Order |  Painting Tips |  Shipping |  International |  Questions? |  Site Map |  HOME

Flexi-Clear #60

Elastomeric Clear Sealer, Finish


Please take note that Flexi-Clear is an elastomeric sealer perfect for many applications, but without insulating properties. It can be made to insulate by the addition of ThermaCels, but it will then have an opaque or "milky" look.


Flexi-Clear is a Clear Acrylic Elastomeric Sealant designed to seal and protect a wide range of surfaces including wood homes, stone, brick, masonry and concrete, roofing materials and reflective roof coatings.
All white roof coatings start losing their reflectivity properties due to accumulated dirt and other contaminates. Until now clear protective coatings for elastomeric base coatings were not available due to their lack of flexibility which is necessary as roof coatings are designed to expand and contract with a roof's movement.
Flexi-Clear is based on the same resins used in our insulating roof coatings and features the same elongation, expansion and contraction properties of those coatings.
Flexi-Clear also features outstanding adhesion to the applied surface, elongation and recovery capabilities, a combination of UV absorbers and mildewcides enabling it to resist the effects of the most severe climatic conditions.
Now all roof coatings can be protected from surface contamination enabling them to perform as intended by reflecting radiant heat away from the buildings interior.
This self cleaning clear coat works much the same way as the clear coatings designed and used on automobile finishes.


Flexi-Clear is truly an all-purpose clear sealant and protectant, suitable for virtually any application.
Color: Milky White, dries clear.
Volume Solids: 41% 2%
Flash Point: Same as water.
Coverage: 150-200 sq.ft. per gallon depending on the porosity of the surface.
Recommended Coverage: The number of coats depends on surface porosity; however, one coat is all that is normally needed on a well sealed surface. Un-coated roof shakes or shingles require two full coats.
Min. Surface Application Temp.: 7.2C / 45F. Do not allow to freeze.
Drying Time: Will depend on climate conditions. Allow at least 2 hours drying time between coats. First coat must be thoroughly dry before applying second coat.
Limitations Not suitable for below grade use.
Surface Preparation Surface must be clean and free from dirt, dust, grease, oil, mildew, wax, loose paint. Roof Shingles should be sealed with #1220 Bond-it, our roof grade bonding/sealer for roofs to lock in loose granular minerals.
Application: Best applied by airless spraying or roller. If spraying, use a .x15 - .x19 tip and back-roll (finish with a roller) to assure an even film of coating. Areas that are too thick may dry unevenly.
Can be applied with a short nap roller cover.
Clean Up Cleanup immediately after use with soap and water.

CAUTION:
Do not apply within two hours of sunset, rain, fog or freezing temperatures. All coatings must be completely dry before exposing to water or foot traffic. Keep all containers covered when not in use. Keep away from children.
Available in 1 Gal and 5 Gal containers
$39.95 Per Gal...5 Gallon $199.75

buy insulating paint  Or  order insulating paint

House Paint Roof Coatings Clear Coatings
Primers-Sealers Fire Retardants Specialty Coatings Supplies-Sundries

environmentally safe paint and coatings  Order |  Painting Tips |  Shipping |  International |  Questions? |  Site Map |  HOME buy with confidence

Mailing Address: Hy-Tech - P.O. Box 216, Melbourne, FL 32902
USA Order Toll Free: 1-866-649-8324 * Outside USA Order: 321-984-9777
Tech Support: 321-984-9777 * Fax: 321-984-1022

and terms of use- All Rights Reserved