insulating paints and insulating paint additives Space Age Energy Saving
Insulating Paint & Paint Additives
spaceage insulating ceramicsA NASA Technology Spinoff Company 2003spaceage insulating ceramics
Order |  Painting Tips |  Shipping |  International |  Questions? |  Site Map |  HOME

Shields All #50

All purpose Clear Sealer

SHIELDS-ALL  is a clear, 100% acrylic water repellant, sealer, and latex paint reinforcing additive which is formulated to provide superior protection from moisture penetration and the effects of weathering on a variety of properly prepared substrates.
Once applied it may be painted over with any type of paint or coating and may also be tinted and used as a latex stain for wood surfaces.
Shields All may be mixed with any latex paint or stain to improve the flow properties and weatherability at a ratio of 1 part Shields All to 10 parts paint. Shields All cleans up easily when wet with water, is non-toxic to humans, animals and vegetation.
ENVIRONMENTALLY SAFE! Mildew Resistant Interior or Exterior Use.

SHIELDS-ALL acrylic water repellant and sealer can be applied to a wide range of above grade, interior and exterior surfaces including:
Concrete, stucco, brick, wood, masonry, metal, stone, drywall, tile, grout, Adobe, wood siding, masonite, asphalt and fiberglass shingles, split face block, EFIS, previously painted surfaces, chalked or alkaline surfaces.

SHIELDS-ALL can be applied to green masonry or concrete as a curing agent and surface conditioner to reduce alkali. In addition to providing water repellant protection, SHIELDS-ALL can be used as an under-seal/primer to promote adhesion with latex and elastomeric coatings.

APPLICATION :
SHIELDS-ALL is supplied ready to use. DO NOT THIN. Mix thoroughly prior to use. Easily applied with a quality brush, roller, airless spray and low pressure hand pump sprayer. Always apply material to test panel prior to general application.
Porous Vertical Surfaces: Start first coat application at the top of the wall. Apply flood coat with a 6"-8" rundown and back-roll material into surface voids. Apply second coat when the first coat is dry.
Vertical Concrete Surfaces: Surfaces shall be clean and free of form oils and release agents.
Start first coat application at the top of the wall. Apply saturation coat and back-roll materials.
Apply second coat when the first coat is dry.
Horizontal Concrete Surfaces: Apply 2 saturation coats to damp concrete to assist the curing and hardening process. Apply 1 saturation coat to existing horizontal concrete surfaces to dust proof surfaces. Remove excess standing or ponding materials with a clean roller.
Brick: Apply 1 saturation coat with run-down and back-roll material. Apply second saturation coat when the first coat is dry. Caution: New brick surfaces shall be allowed to weather for 12 months prior to application of material.
Stucco/Plaster: May be applied to stucco or plaster during the curing process or when fully cured. Apply 1 saturation coat and back-roll materials. Apply second saturation coat when the first coat is dry.
Chalked Surfaces: Apply 1 coat to chalked surfaces. Allow material to dry and check surface for chalking. Apply a second coat to surfaces as needed to control remaining surface chalk.
Wood: Surfaces shall be clean and bare. Pre-treat knots with a small amount of material. Apply a minimum of 2 saturation coats to wood surfaces. Apply second coat when the first coat is dry.

Coverage: Covers approximately 75-300 square feet per gallon depending on type of application and porosity of the surface to be treated.
Dry Time: Dries to the touch in 1 - 2 hours, may be re-coated in 3 - 4 hours depending on conditions. Clean up any spills, painting tools and equipment with warm soapy water.

Available in 1 Gal, 5 Gal, and 55 Gal drums
$39.95 Per Gal...5 Gallon $199.75

buy insulating paint  Or  order insulating paint

House Paint Roof Coatings Clear Coatings
Primers-Sealers Fire Retardants Specialty Coatings Supplies-Sundries

environmentally safe paint and coatings  Order |  Painting Tips |  Shipping |  International |  Questions? |  Site Map |  HOME buy with confidence

Mailing Address: Hy-Tech - P.O. Box 216, Melbourne, FL 32902
Fax: 321 984-1022

Copyright 2003-2007 and terms of use- All Rights Reserved