insulating paints and insulating paint additives Space Age Energy Saving
Insulating Paint & Paint Additives
spaceage insulating ceramicsA NASA Technology Spinoff Company 2003spaceage insulating ceramics
Order |  Painting Tips |  Shipping |  International |  Questions? |  Site Map |  HOME

XClear

Hard Acrylic Clear Sealer

XClear  is a clear, 100% acrylic water repellant, sealer, and latex paint reinforcing additive which is formulated to provide superior protection from moisture penetration and the effects of weathering on hard to bond to surfaces.
XClear cleans up easily when wet with water, is non-toxic to humans, animals and vegetation.
ENVIRONMENTALLY SAFE! Mildew Resistant Interior or Exterior Use.

XClear acrylic water repellant and sealer can be applied to a wide range of above grade, interior and exterior surfaces including:
Concrete, stucco, brick, wood, masonry, metal, stone, drywall, tile, grout, Adobe, wood siding, masonite, split face block, EFIS, previously painted surfaces, chalked or alkaline surfaces.

APPLICATION :
XClear is supplied ready to use. DO NOT THIN. Mix thoroughly prior to use. Easily applied with a quality brush, roller, airless spray and low pressure hand pump sprayer. Always apply material to test panel prior to general application.
Non-Porous Vertical Surfaces: Start first coat application at the top and spread a thin even coat, avoid over brushing. Apply second coat when the first coat is dry.
Porous Vertical Surfaces: Start first coat application at the top of the wall. Apply flood coat with a 6"-8" rundown and back-roll material into surface voids. Apply second coat when the first coat is dry.
Vertical Concrete Surfaces: Surfaces shall be clean and free of form oils and release agents.
Start first coat application at the top of the wall. Apply saturation coat and back-roll materials.
Apply second coat when the first coat is dry.
Horizontal Concrete Surfaces: Apply 2 saturation coats to damp concrete to assist the curing and hardening process. Apply 1 saturation coat to existing horizontal concrete surfaces to dust proof surfaces. Remove excess standing or ponding materials with a clean roller.
Brick: Apply 1 saturation coat with run-down and back-roll material. Apply second saturation coat when the first coat is dry. Caution: New brick surfaces shall be allowed to weather for 12 months prior to application of material.
Stucco/Plaster: May be applied to stucco or plaster during the curing process or when fully cured. Apply 1 saturation coat and back-roll materials. Apply second saturation coat when the first coat is dry.
Chalked Surfaces: Apply 1 coat to chalked surfaces. Allow material to dry and check surface for chalking. Apply a second coat to surfaces as needed to control remaining surface chalk.
Wood: Surfaces shall be clean and bare. Pre-treat knots with a small amount of material. Apply a minimum of 2 saturation coats to wood surfaces. Apply second coat when the first coat is dry.

Coverage: Covers approximately 75-300 square feet per gallon depending on type of application and porosity of the surface to be treated.
Dry Time: Dries to the touch in 1 - 2 hours, may be re-coated in 3 - 4 hours depending on conditions. Clean up any spills, painting tools and equipment with warm soapy water.
As with all our clear coatings, Hy-Tech Insulating additive may be added which will reduce heat transfer through the coating substantially

Available in 1 Gal and 5 Gal cans
$42.95 Per Gal...5 Gallon $214.75

buy insulating paint  Or  order insulating paint

House Paint Roof Coatings Clear Coatings
Primers-Sealers Fire Retardants Specialty Coatings Supplies-Sundries

environmentally safe paint and coatings  Order |  Painting Tips |  Shipping |  International |  Questions? |  Site Map |  HOME buy with confidence

Mailing Address: Hy-Tech - P.O. Box 216, Melbourne, FL 32902
Fax: 321 984-1022

Copyright 2003-2007 and terms of use- All Rights Reserved